Recycled Hook Holders & Crocheted Covers

  ✂︎

Favorite

Comment

List

       

Share

• Step 1

  Tutorial and suggestions for creating your own Holders using empty pens, ETC.

  Gather empty holders - including ball-point pens, permanent markers, highlighters, felt-tips & mechanical pencils.

• Step 2

  Separate Metal Tip from Plastic Tip holders.

• Step 3

  Collect Hooks (Keep in mind that larger/wider hook shafts will require bigger/thicker holders.)

• Step 4

  Locate Tools - sharp knife, small hack saw & file/s. May also need some of the following - emery boards, diamond finger nail files or fine sandpaper; scotch tape; water based or permanent glue and stuffing - like aluminum foil.

• Step 5

  Select a flat surface to work - such as a desk top or table.

• Step 6

  Small container to hold loose parts.

• Step 7

  Choose a holder - unscrew the sections and/or remove tip if possible.

• Step 8

  Set aside the inside pieces - but don't throw away, especially the springs. These parts may help stabilize the hook inside the cover.

• Step 9

  Test the hook by inserting from inside the cover body down through the tip end - but don't force it; should slip through with minimal pressure if the size is compatible to the tip opening.

  **See Example #1, above.

  NOTE: Some holders may require sliding the hook shank into the tip end after modification, and some
  metal tips can be removed allowing the holder to be modified if needed. See **Example #2 above.

• Step 10

  If the hook is good fit - try assembling the rest of the holder/cover for length. Assemble the rest of the cover. If hook is too short or loose inside the holder - try adding springs, other inside pieces or stuffing such as aluminum to secure the hook in place. If hook is too long - try a different one or consider cutting the end of the hook shank to the required length.

  NOTE: *Most metal tip covers only fit very small crochet hooks such as Size "A" to "E" and "0" or smaller.

• Step 11

  Larger sizes & thicker hooks usually require bigger openings as the hook head won't fit through most metal tips. Plastic holder tips can usually be altered with careful handling.

  NOTE: Trim Plastic Pen and Marker tips with a sharp knife or small hack saw, then sand to smooth edges.
  Be aware many plastics split easily, so have patience. Remove small sections slowly and carefully. Don't be
  discouraged if the plastic breaks or splits - cut below the damaged area and try again.

• Step 12

  If the hook sheath is too narrow or short to fit snuggly inside the cover, wrap with a few layers of Scotch Tape or fill interior with springs, extra parts or stuffing. The flat (thumb) space on most hooks can also help stabilize the hook, and it's possible to glue the hook in place unless you wish to keep the cover available for use with other hooks.

• Step 13

  Be sure to leave enough length from the hook head to the tip of the cover to accommodate a variety of threads or yarns
  when working on projects. If the shank is to short it can interfere with creating the stitches. **See Examples #1 & #2 for the
  length of hook shank that worked best for me.
  NOTE: See completed hook holders on the SITE below.*
  *LadyWillow Designs© Hook Covers, Sleeves & Holders pictures from crafts photos on webshots
  http://home-and-garden.webshots.com/album/570614118NmjSkU
  SUGGESTIONs...
  When regular Hook is too short - use recycled pen parts or stuffing to fill interior and stabilize hook - glue if necessary. Broken
  hooks work well with shorter holders. /;)
  Rather than trying to fit a specific hook to a favorite cover - keep a selection of empty holders and hooks in reserve to create
  the Holders or Covers. Be flexible and have fun. /;)
  Some hooks, like very large or very small sizes, may not work well with recycled holders, or a softer surface may be required,
  especially for cold, metal hooks. See the list below for additional ideas.
  Custom Cover & Holder Options ...
  1. Crocheted Covers or Sleeves - See SITE above.
  2. Fimo or Polymer/Sculpy Clay
  3. Plastic Tubes - such as oxygen tubing

Comments

Leave your comment

Käpt´n Toasterkopf · Germany, Pennsylvania, US · 53 projects 3rd June 2009

That´s good timing! I just broke a hook so I can try that right now.
Thank you :3

Reply

Jet H. · Haarlem, North Holland, NL · 108 projects 2nd June 2009

great idea! I have difficultys with holding small crockets hooks so thanks!!!

Reply

Käpt´n Toasterkopf · Germany, Pennsylvania, US · 53 projects 2nd June 2009

Wow, that´s timing! I just broke a hook.
So thank you for this tutorial ^-^

Reply

Cupcake girl · U.S. Air Force Academy, Colorado, US · 28 projects 31st May 2009

That's a great idea!

Reply

LadyWillow · 1 project 31st May 2009

Thanks for the compliment Dragoness - from one recycler to another I like the whimsical Holders to cheer me up on gloomy days and use all of them at one time or another to aid the hands.

Reply

Dragoness (Cvania Lover) · Porto Alegre, State of Rio Grande do Sul, BR 31st May 2009

What a wonderful idea! It's great because you don't throw the pens away and also because the resulting tool is way more confortable to use. I love it!

Reply