3D Origami Clematis

  ✂︎

Favorite

Comment

List

       

Share

• 

  Step 1

  Octagonal Base

  Make the creases.

• 

  Step 2

  Turn over
  Rotate

• 

  Step 3

  Make the creases.

• 

  Step 4

  Bring together along the creases.
  Rotate

• 

  Step 5

  Open the flap out and then flatten it down.

• 

  Step 6

  Fold the remaining three flaps in the same way.

• 

  Step 7

  Cut at the position shown and then unfold.

• 

  Step 8

  This is how it looks on completion

• 

  Step 9

  CORE ● Made from the octagonal base

  1. Crease in line with the middle.

• 

  Step 10

  2. Fold the remaining seven flaps in the same way.

• 

  Step 11

  3. Fold only one flap.

• 

  Step 12

  4. Open the flap out and then flatten it down.

• 

  Step 13

  5. Bring the pleats together so that they follow each other round. (see p.36)

• 

  Step 14

  6. Turn over

• 

  Step 15

  7. It will look like this.

• 

  Step 16

  8. Bring together along the creases, as shown in the illustration.

• 

  Step 17

  How it should look in mid-fold

• 

  Step 18

  9. Fold the edge in line with the middle.

• 

  Step 19

  10. Fold the top again.

• 

  Step 20

  11. Fold the remaining seven flaps in the same way as in steps and .

• 

  Step 21

  Rotate

• 

  Step 22

  This is how it looks on completion!

• 

  Step 23

  FLOWER ● Made from the octagonal base

  1. Crease in line with the middle.

• 

  Step 24

  2. Fold the remaining seven flaps in the same way.

• 

  Step 25

  3. Make a crease at the centre only by folding in line with the creases that you made in step .

• 

  Step 26

  4. Fold the remaining seven flaps in the same way.

• 

  Step 27

  5. Crease in line with the creases that you made in step .

• 

  Step 28

  6. Fold the remaining seven flaps in the same way.

• 

  Step 29

  7. Fold only one flap.

• 

  Step 30

  8. Open the flap out and then flatten it down.

• 

  Step 31

  9. Bring the pleats together so that the flaps follow each other round.

• 

  Step 32

  Turn over

• 

  Step 33

  11. Bring together along the creases shown in the illustration.

• 

  Step 34

  How it should look in mid-fold

• 

  Step 35

  12. Crease along a line connecting the points marked○ and ○.

• 

  Step 36

  13. Fold along the crease that you made in step .12

• 

  Step 37

  14. Fold along the creases that you made in step .12

• 

  Step 38

  15. Fold the remaining seven flaps in the same way as in steps 12 to

• 

  Step 39

  16. Fold the middle towards you,

• 

  Step 40

  18. and then fold the section that sticks out at the front to the opposite side.

• 

  Step 41

  19. Fold the remaining seven flaps in the same way as in steps 17 and 18.

• 

  Step 42

  ...

• 

  Step 43

  21. Slit at the points shown.

• 

  Step 44

  ...

• 

  Step 45

  23. Turn the model out by pushing on the bottom with your fingers.

• 

  Step 46

  This is how it looks on completion!

• 

  Step 47

  Flower core
  Glue
  Flower
  20 gauge wire, 
curled at the tip
  Pass a length of 20 gauge wire, curled at the tip, through the flower, and glue on the core from above.

Comments

Leave your comment