Teal Pearl Resin Heart With Red Crystal Accent

A pretty teal resin heart you can wear!

Posted by Erk N' Jrk Creations

About

Resin can either be easy or hard as heck! LOL It is still both for me at times! However, I saw that someone was looking for a tut on resin pouring, so here goes LOL Not sure how well I can explain this, but I thought I'd give it a go!

Share

You Will Need (4 things)

  • Epoxy Resin
  • Mixing Cup(s)
  • Resin , Paint, Or Poly Clay Pigments
  • Small Crystals

Steps (5 steps, 540 minutes)

  1. 1

    Sorry guys, again I don't have any how-to pics. I'm going to be mixing some resin soon, so I'll take pics then and post them in another tut. Hopefully this will get ya started though!

    Step 1: Figure out what type of resin you want to use! There are tons of different types. The most important thing to remember with resin is that you mix it in two equal parts. One part resin, one part hardener. The most typical resin for jewelry is Castin Craft. The resin can be a bit expensive, but a little goes a long way.

  2. 2

    Step 2. With all resins you need mixing cups (preferably with measurments on them. it makes life a lot easier and something that you don't mind throwing away)In one cup measure out some resin...in the second cup measure out some hardener (EQUAL parts of each). Now this is important..pour the resin and the hardener (after it's measured) into a third mixing cup. Mix this together for about 2 minutes.

  3. 3

    Step 3: Molds, molds, molds! There is a huge argument over whether or not you need to use a mold release spray (which at times can go for about 6 bucks a bottle!). I've poured resin with and without it, but I tend lean towards using it. They sell molds especially for pouring resin..www.sherrihaab.com is a good one..or you can find some on Ebay as well. Candy and candle molds are a bit more difficult because they tend to be a bit thinner and when you remove your resin, there's no telling if the mold will survive. Once you have picked out your mold..move on to the next step.

  4. 4

    Step 4: There are a ton of different ways to do your resin, but I'm going to tell you the two ways that I do it..

    1 - Solid colored pigment...you can add pigments to the resin to color it. There are pigments sold especially for resin, or you can use pigments for poly clay, some paints, and even some embossing powders will work. In the case of the blue heart that I made, I used Pearl Ex Pigments by Jaquard Products.

    2 - Clear pouring with embedded elements. This is a two part process actually. You can embedd anything into resin this way..photos, sprinkles, candy, toys...I've even seen bugs and teeth (ick lol). You pour a small amount of your resin, about 1/8 - 1/4 thick and wait....I know! Sucks right? But you need to wait for that bottom layer to cure a bit before adding your focal part. Once you add your focal part, pour more resin on top and...you guessed it...Wait again! (I've had some things that have had a curing time of 3 days..::sigh::)

  5. 5

    Step 5: Once your pieces have fully cured (and this is important! LOL I've been impatient with resin and tried to pop it from the mold too early and it's just a sticky mess!)pop your pieces out.

    You may want to sand down the outer edges because they can get a lil uneven after pouring. I use a dremel tool for this. You can also drill a hole in your resin and either attach a jump ring, or drill on top and screw in a screw eye for hanging.

    I hope I didn't confuse you too much and if you have any questions, I"ll try my best to answer them!