Metal Stamped Cuff

Metal stamped cuff from flat wire

Posted by Thepotatolarcenist

About

I know I'm probably about 5 years too late to this trend but hey, better late than never right? Despite being a beginner (I don't use that term lightly, I started like a week ago), I thought that maybe a 'For beginners, by beginners' type of tutorial would be useful for some people.

I have a more detailed version on my blog where I also elaborate about the materials and where to get them so check that out if you're interested

http://thepotatolarcenist.blogspot.sg/2013/12/metal-stamping-game-is-afoot.html (I can't seem to get it to work in the promotion bar :/)

Share

You Will Need (3 things)

  • Metal Stamp
  • Flat Wire
  • Hammer

Steps (22 steps, 30 minutes)

  1. 1

    Materials
    -Metal stamps
    -Hammer
    -Flat Wire (Mine's 5x1mm)
    -Hard surface to stamp on/ Bench Block
    -Permanent Marker
    -Masking Tape

  2. 2

    Additional Materials for flat wire
    -Wire cutter
    -File
    -Sand paper (400 grit)
    -Nail buffer

  3. 3

    For a cuff, take the exact measurement of your wrist and subtract 1/2 an inch. That will be the amount of flat wire needed. So since my wrist is 5.5inches, my wire needs to be 5 inches

  4. 4

    Mark the middle of your cuff

  5. 5

    Decide on your phrase and number each character, including spacing, to find the middle of your phrase. This is where the previously marked center should be

  6. 6

    Lay out your stamps. I prefer to start with the second half of the phrase. If you start from the first half, start from the last letter of the first half ('I' for me) and go backwards.

  7. 7

    Stamp away! It's hard to see in the photo but you should be able to see the reflection of the metal stamp in the metal. Use that reflection to guide you when you stamp.

    Use masking tape or any tape really to make sure you stamp in a straight line.

  8. 8

    This is what it should look like when it's done!

    If you're curious, since I didn't buy a punctuation set, I improvised with a 1.4mm flat screwdriver as the apostrophe in "I've"

  9. 9

    Ink up your letters! If you prefer how it looks au naturel, then great! But if you want your characters to stand out more, then you're gonna have to use a permanent marker to colour them in. Just make sure that you get ink into all the grooves

  10. 10

    Inked

  11. 11

    Use a tissue or a damp rag to wipe off the excess ink .

    Most people use a sharpie but I find that sharpie ink is harder to get out. I used Cretacolor and this ink comes off with a tissue paper. I will admit that Sharpie's ink pops better though.

  12. 12

    Cleaned

  13. 13

    Since flat wire has to be manually cut, the edges are usually a little sharp and stabby. So the edges need to be rounded

    Start by snipping off the 90 edges

  14. 14

    Round the edges by filing it in the depicted motion. I suggest holding your file in place and moving the flat wire against it.

  15. 15

    When you're done, it should look like this

  16. 16

    This is optional but I find that filing this edge makes it less scratchy when the cuff is slid onto the wrist.

  17. 17

    To make it smoother, sand it on 400 grit sand paper. Don't forget the edge that was filed in the previous step.

  18. 18

    Lastly, buff it until it's shiny

  19. 19

    Shiny!

  20. 20

    Now, it's shaping the cuff. You could use a bracelet mandrel or nylon jaw bending pliers but those are about $15 and $20 respectively ie out of my price range.

    First, wrap it around anything cylindrical to get the C shape in the second picture. Then hold it as depicted and apply pressure with your thumbs

  21. 21

    And you should get this shape!

  22. 22

    And voila, you're done! Now show off your bracelet to the world