https://www.cutoutandkeep.net/projects/liberty-kimono • Posted by Quadrille
Add a touch of old-fashioned glamour to your daily routine with this slinky wrap-around robe, which combines two richly-hued abstract Liberty prints in different textures: ‘Bailando en Mis Suenos’ Balcombe Silk, trimmed with another silk, ‘Combe’ Harcourt Crepe de Chine. It is a comfortable UK size 12, which finishes at mid-calf. Hold the pattern against you before cutting out the fabric, to double check the length and adjust it as necessary for a longer or shorter version. Remember that you will need more fabric for a full-length kimono. Finished size Size 12, with mid-calf length Each square = 2.5cm Note: Seam allowance (1.5cm) is included in pattern-piece size. Cutting out Make a paper pattern piece of all the pieces needed for the kimono, including the rectangles for the front band, cuff, belt and belt loop, and use these to cut the fabric pieces. Transfer all markings onto your pattern pieces. Cut all pieces on straight grain of fabric except where instructed otherwise. from main fabric: • Cut 1 back, on the fold • Cut 2 fronts (1 reversed) from contrasting fabric: • Cut 2 front bands, on the bias, each 11 x 127cm • Cut 2 cuffs, on the bias, each 11 x 44cm • Cut 2 belt pieces, each 11 x 66cm • Cut 2 belt loops, on the bias, each 3.5 x 15cm note: Cut one or two 5mm slits into the seam allowance at each of the points marked on the pattern: these will help you line up the pieces exactly when you pin them together.
Add a touch of old-fashioned glamour to your daily routine with this slinky wrap-around robe, which combines two richly-hued abstract Liberty prints in different textures: ‘Bailando en Mis Suenos’ Balcombe Silk, trimmed with another silk, ‘Combe’ Harcourt Crepe de Chine. It is a comfortable UK size 12, which finishes at mid-calf. Hold the pattern against you before cutting out the fabric, to double check the length and adjust it as necessary for a longer or shorter version. Remember that you will need more fabric for a full-length kimono. Finished size Size 12, with mid-calf length Each square = 2.5cm Note: Seam allowance (1.5cm) is included in pattern-piece size. Cutting out Make a paper pattern piece of all the pieces needed for the kimono, including the rectangles for the front band, cuff, belt and belt loop, and use these to cut the fabric pieces. Transfer all markings onto your pattern pieces. Cut all pieces on straight grain of fabric except where instructed otherwise. from main fabric: • Cut 1 back, on the fold • Cut 2 fronts (1 reversed) from contrasting fabric: • Cut 2 front bands, on the bias, each 11 x 127cm • Cut 2 cuffs, on the bias, each 11 x 44cm • Cut 2 belt pieces, each 11 x 66cm • Cut 2 belt loops, on the bias, each 3.5 x 15cm note: Cut one or two 5mm slits into the seam allowance at each of the points marked on the pattern: these will help you line up the pieces exactly when you pin them together. THE LIBERTY BOOK OF HOME SEWING by LIBERTY, published by Quadrille (£20, hardback). Photos ©KRISTIN PERERS; Text ©LUCINDA GANDERTON.
Neatening the raw edges of the front and back pieces Set your sewing machine to a large zigzag stitch or other overlocking stitch. Using matching sewing thread, machine stitch along each of the shoulder and underarm/side edges of the front and back pieces.
Making the belt loops Following the technique instructions on page 67 for the jewellery roll ties, make the two belt loops into rouleaux. Fold them in half and pin to the back piece on the marked waistline matching the raw edges. (Check first that the waist in the right position for you, and adjust as necessary.)
Stitching the front and back pieces together With right sides together, pin the two front pieces to the back, matching the notches in the seam allowance. Machine stitch together, leaving a 1.5cm seam allowance.
Clipping the curved seams Work a second line of machine stitching over the first to reinforce the curved part of the underarm seam. Cut three or four small notches into the seam allowance here so that it will lie flat. Press all of the seams open and turn the kimono right side out.
Preparing the cuffs Pin the short ends of the cuffs together, with right sides facing and machine stitch 1.5cm from the edge. Press the seams open, then press back a 1.5cm turning around the outside edge.
Stitching on the cuffs With right sides together, pin the cuffs to the sleeves, matching the seams to the underarm seams. Machine stitch, 1.5cm from the edge, then trim the seam allowance to 1cm. Press the seam allowances towards the cuffs.
Finishing the cuffs Turn the kimono wrong side out and fold the cuffs in half so that the folded edges lie along the stitched lines, concealing the seam allowance. Pin in place and slipstitch the fold to the seam allowance, as close as possible to the stitching.
Turning up the hem Press a 1cm turning along the bottom edge of the kimono, then press under 3cm more. Pin in place, and hand or machine stitch down, easing in any extra fullness. Tack the raw edges together at the ends of the hem.
Stitching the front bands together Pin and stitch the two front band pieces together end to end: this seam will lie at the centre back. Press the seam open, then press a 1.5cm turning all the way along one long edge.
Adding the front band With right sides together, pin the band seam line to the kimono centre back. Pin each edge out to the bottom corners of the two front pieces. The two ends will hang below the hem. Machine stitch, leaving a 1.5cm seam allowance. Press the seam outwards, towards the band. Press under the two ends of the front band so that they are in line with the hem
Finishing the front band Fold the band to the inside of the kimono so that the long folded edge is lined up to the seam line. You will need to ease it around curved edges of the two front pieces. Pin in place and stitch down by hand or machine. Slipstitch the bottom edges of the facing together on the left and right fronts.
Making the belt With right sides together, pin and stitch the two belt pieces together and press the seam open. Fold the belt in half lengthways with right sides together. Pin, then stitch together 1cm from the edge, leaving an opening of approximately 15cm near the centre seam. Clip the corners, then turn right side out through this opening. Press flat and slipstitch the opening closed.