Cut Out + Keep

Headband Rack

It's much neater then a box.

https://www.cutoutandkeep.net/projects/headband-rack • Posted by Jessy

So I was using this little box to store my headbands, and it wasn't working out too well. I had the bands hanging over the side of the box, and I had so many jammed in there, that when I pulled one out, three more came with it. I've been trying for months to think of some other way to store them. And then it dawned on me. I keep my hair clips on a strip of ribbon hanging over the side of my dvd stand. So why couldn't I do something similar with the hairbands.

You will need

Project Budget
Cheap

Time

2 h 00

Difficulty

Pretty Easy
Medium dscf3397 Medium dscf3393 Medium dscf3519

Description

So I was using this little box to store my headbands, and it wasn't working out too well. I had the bands hanging over the side of the box, and I had so many jammed in there, that when I pulled one out, three more came with it. I've been trying for months to think of some other way to store them. And then it dawned on me. I keep my hair clips on a strip of ribbon hanging over the side of my dvd stand. So why couldn't I do something similar with the hairbands.

Instructions

  1. I got a thick poster board, grosgrain ribbon and some vinyl drawer liner from the dollar store. This whole project cost me $3.00.

  2. Small dscf3399

    First I had to cut the board. I kept the length of the board, and cut it wider then my headbands. I want my headbands to lay flat against it.

  3. Small dscf3377

    I got this vinyl drawer liner to cover the board. I would have used wrapping paper, but I couldn't find anything that wasn't flowery or colorful. I found this in the kitchen area. It was just wide and long enough to cover the width and length of my board. This stuff looks wider and longer then it really is. It's 12x30in. I wanted the pattern to line up just right on the board, so I wasn't worried about wasting the vinyl and saving scraps.

  4. Small dscf3503

    If your using regular wrapping paper or fabric or something else to cover the foam board, then you'll want to lay the board out on the paper and trace out enough to cover the board.

  5. Small dscf3505

    I used rubber cement and covered both the board and the back of the liner. Once it dried I very carefully laid it tight to the board. Getting the pattern to line up just right was the hardest part. If your using regular wrapping paper, I suggest gluing a small section at a time. The 2nd board I made had glue bubbles cause I laid the paper down all at once. I would have used glue sticks for the thinner paper if I had any.

  6. Small dscf3369

    Then I measured out were I want the ribbon loops to sit. I used a sharpie to mark it. I marked 15 spaces on this one. Make sure to leave space between the loops for the bigger headbands. If the thicker band loops are to close together then the band won't lay close to the board.

  7. Small dscf3513

    Then I used a box cutter to cut out the notches. Make sure to cut a little wider then the ribbon your using.

  8. Small dscf3511

    I used grosgrain ribbon for this project. I thought the texture of the ribbon would help hold onto the headbands better then other ribbons. But you can use what you like. I measured the ribbon around the thickest part of my thickest band. Then I added two and a half inches for the parts that will be glued to the back of the board.

  9. I cut 4 strips of ribbon 6 inches long. This will be the loops for the wider headbands. Then I cut 11 strips 4 inches long for the smaller band loops.

  10. Small dscf3364

    Then I pushed one end of the ribbon through the hole I cut at the bottom of the board.

  11. Small dscf3366

    Then I pushed in the other end of the ribbon. Repeat steps 9 & 10 for all ribbon loops.

  12. Small dscf3383

    You should have something like this on the front.

  13. Small dscf3381

    And this is what the back should look like.

  14. Small dscf3378

    I used my glue gun to glue down the ends of the ribbon on the back of the board. I sized it by sliding a headband through and pulling the ribbon tighter, but not to tight. If the ribbon is to loose or too tight, then the band will fall out easy or it'll be to hard to get in or out. Do this for all the loops. Make sure to make some loops smaller and some bigger. Not all headbands are the same size. I put the smallest loops at the top of the board and the biggest at the bottom.

  15. Small dscf3389

    After I glued all the other ribbon ends down, this is what that should look like. I also glued down the vinyl liner edges.

  16. Small dscf3385

    Cut a small scrap of ribbon and glue it down in a loop. Now you can hang it up.

  17. Small dscf3391

    All done. Now you just have to put a headband through the loops.

  18. Small dscf3393

    All finished.

  19. Small dscf3397

    This is mine all full.

  20. Small dscf3519

    This was the second board I did. I'm not really sure why the ribbon loops look so crooked. I cut the holes straight. Oh well, it won't really matter when the headbands are on it. This board holds 22 bands.