Diy Ampersand

Did you know that you can make your own DIY Ampersand, come see how!!

Posted by shonee s.

About

I have been loving all of the art using punctuation marks like # and &. I decided I wanted to see if I could make my own ampersand. Come learn how to make one yourself.

Share

You Will Need (7 things)

  • Putty Knife
  • Small push Pins
  • styro wonder cutter
  • Gold spray Paint
  • Styrofoam Glue
  • floracraft smooth finish
  • 18 in Styrofoam Block

Steps (9 steps, 120 minutes)

  1. 1

    I am pretty excited that my DIY ampersand worked out. I have had my fair share of DIY flops, so it is always fun when they turn out good!
    First of all, can you believe that this ampersand is actually made of styrofoam!!

    Pretty cool, right?!

    Today I am going to show you how you can make this DIY Ampersand.

  2. 2

    You will need:
    18 inch Styrofoam Block
    Floracraft smooth finish (found mine at Walmart)
    Styrofoam glue
    Gold spray paint
    Styro Wonder Cutter
    small push pins
    putty knife

  3. 3

    I have had my Styro Cutter for almost 10 years and have used it a number of times, I have never had any issues with it at all. It looks like they have updated the style, since I purchased this one, to look better than a used toilet paper roll....hahah.

  4. 4

    I added links to a pdf of the ampersand that I used. Print both pages, overlap them a little to get them lined up good, tape the two pieces of paper together and then cut it out.

    & Sign 1
    & Sign 2

    After I was done cutting out the paper, I laid it on the styrofoam and used pins to secure it in place.

  5. 5

    Next, grab your styro cutter because it's time to cut!

    It's pretty easy to use, but please read all of the directions before you begin. Also it might be a good idea to use a corner of the styrofoam to practice and get a feel for how fast it cuts through the styrofoam.

    Caution! The cutter cuts by melting the styrofoam so be careful not to burn yourself.
    Cut out the entire perimeter of the ampersand. Then make three additional cuts as you can see in the picture below, where the three red lines are. You might have to tear the paper in order to cut the holes of the Ampersand out.

  6. 6

    When done cutting, remove the paper and apply the Smooth Finish product on the front and sides of the styrofoam. I didn't bother doing the back since I knew I would be hanging it up. To apply the Smooth Finish use a putty knife, or in my case, a butter knife to evenly spread the white puffy stuff. Keep in mind the directions say to "add a thin layer." I thought that a thin layer would not do the trick, so I added a thick layer. I ended up sanding waaaaaayyyy too much. A thin layer will work. If you want to add more layers it's best to let it completely dry before adding more.

  7. 7

    Allow the Smooth Finish product to dry overnight.
    When fully dry use sandpaper to lightly smooth the entire surface. Then use the styrofoam glue to stick the two pieces back together. You may need to add a small patch of Smooth Finish to cover up the glue seams.

    Here is what mine looked like after sanding it.

  8. 8

    Here is what it looked like after spraying it with gold spray paint. .

  9. 9

    Finished!!
    When I showed my husband the finished product he asked, "is that a piece of metal?" The not-so-even areas of the Smooth Finish also added character, and apparently made it look like metal. Not exactly what I was going for, but I LOVE how it turned out.
    This will be an accent piece for my command center. What do you think? Have you ever cut styrofoam before?