Bondage Cuffs
DIY Shabby Chic Velcro Wrist Restraints
Posted by Gorey DeTails
About
Ever think about making these, because the pre-made ones either look uncomfortable or are crazy expensive?
Me too.
So I thought I'd give it a shot. I used nothing but scraps from other projects, so this didn't cost me anything.. but would still be really cheap for new materials.
I'm pleased with how they turned out but will probably make more once I find the right faux fur or something. Let me know what you think!
Share
You Will Need (6 things)
- Quilt Batting 2 strips approx 3" x 10"
- 8 in Velcro
- Scrap Fabric less than 1/4 yd
- Notions: Thread , Scissors, Pins, Sewing Machine
- 2 D Ring(s)
- vinyl or nylon Strap optional
Steps (15 steps, 120 minutes)
-
1
Measure around your wrist.
I got 7". We'll call this measurement "X". -
2
Measure out your pieces. You'll need:
two "bodies"
If you're using a thicker material such as vinyl or thick velvet you'll need two strips for each side that make up the 'body' and measure (X+2) by 6. Since X for me is 7 inches, mine would measure 9 x 6. If you're quilting the center, like I did you'll need a topside and a backside, and of course, batting.
Two "Straps"
You can use webbing or wide nylon chord, too. Just burn the edges after cutting to prevent unraveling. These should measure about (X+4) by 2. Since mine was 7", that makes my strip 11 by 2.
Optional Binding:
If you're making a quilted one like mine, you will also need enough binding for the circumference of both cuffs.
The fabric I used was exceptionally thin, so I doubled-up on it. -
3
Iron everything flat.
If your 'bodies' are of a tougher material, iron the crease in the middle with the "right" sides together.
If you cut your straps rather than using a nylon strap, iron those in half with the "right" sides together.
Skip to # 9 unless you're doing the quilted version. -
4
If you're making the quilty one, don't forget the binding! I cut mine at about 2" wide. Iron your binding in half if you want, wrong sides together.
Double fold bias tape is also a nice option. -
5
Prepare for top stitching: Pin the top, batting, and backing together, making sure all three layers are aligned.
-
6
Apply top stitching to both cuff bodies. This is a nice opportunity to experiment with freeform quilting since its a nice small piece and your work won't show too much.
-
7
Attach binding, all the way around. There are some really great youtube videos concerning a clean-looking binding and for joining the ends of your binding.
-
8
Ta-da!
You did this to the other side, too, right? -
9
If you're using a thicker (unquilted) material, stitch up the long, open side and turn it right-side-out. Press the body so that the seam runs right down the middle of one side. You will hide this seam with the thinner strip. Then, flip a small edge of the tube in on itself and sew it shut on both sides.
-
10
Attach the ROUGHER side of the Velcro to one side of a strip by stitching all the way around the perimeter. If you're using a wider strip, make an X through the center with straight stitch.
Velcro should be about 4"... I was using some scraps and butted two pieces together that measured about 3 3/4" -
11
Pin & stitch your strip to the body. Just stitch the perimeter of the Velcro - not the entire strip!
-
12
Slide the D ring up the strip to butt up against the Velcro seam.. continue sewing strip to the other half of the cuff.. leaving a little bubble in the strip over the D ring (so that when it's bent over a wrist, the cuff doesn't buckle). A length of the strip will hang over the edge of the cuff.
-
13
Flip the cuff over. Attach the FUZZY side of the Velcro to the other side of the strip. Again... on the *opposite* side of the cuff than the D ring.
Mine is two different colors because I was using leftovers from two different projects. -
14
... Trim all of your threads... Hopefully your thread matches your fabric, unlike mine.
-
15
You're done!