Cut Out + Keep

Al Fresco Placemat

Fun with Fat Quarters

https://www.cutoutandkeep.net/projects/al-fresco-placemat • Posted by Search Press

34cm (13¼in) diameter Make placemats with cutlery catchers for outdoor dining. Using strips that are sewn at angles gives the circular mats a crazy-patch appeal. Preparation for each placemat Cut four strips of 7 x 35cm (2¾ x 13½in) from one 
fat quarter and five strips of 7 x 35cm (2¾ x 13½in) from the other Cut two small strips of 12 x 7cm 
(4¾ x 2¾in) for the cutlery catchers

You will need

Project Budget
Cheap

Time

4 h 00

Difficulty

Nice & Simple
Medium 110425 2f2015 08 14 091350 fat%2bquarters page%2b68 086 Medium 110425 2f2015 08 14 091808 fat%2bquarters page%2b69 043 Medium 110425 2f2015 08 14 091812 fat%2bquarters page%2b71 045

Description

34cm (13¼in) diameter Make placemats with cutlery catchers for outdoor dining. Using strips that are sewn at angles gives the circular mats a crazy-patch appeal. Preparation for each placemat Cut four strips of 7 x 35cm (2¾ x 13½in) from one 
fat quarter and five strips of 7 x 35cm (2¾ x 13½in) from the other Cut two small strips of 12 x 7cm 
(4¾ x 2¾in) for the cutlery catchers

Instructions

  1. Small 110425 2f2015 08 14 100612 screen%2bshot%2b2015 08 14%2bat%2b11.06.14

    Lay two contrasting strips right sides together. Keeping the top-left edges together, swing the bottom of the upper layer to the right, so that the bottom-left edge of the upper layer is 1cm (3/8in) from the right-hand edge of the lower layer. Pin the two pieces together then stitch with a 5mm (¼in) seam. Cut off the excess underlayer.

  2. Flip the top layer over and add another strip, this time, with top-right edges together and the bottom-right edge moved diagonally across to the left. Again stitch with a 5mm (¼in) seam. Flip and continue adding contrasting strips at angles until all nine are used. Press all the seams.

  3. On the reverse of the fabric, draw around the bowl or plate with a disappearing or fadeaway marking pen. Cut out 1cm (½in)outside the marked line; the marked line will be your stitching line.

  4. Cut the same size circles from backing fabric and wadding (batting). 
Use two layers of insulated wadding (batting) to protect your surfaces 
from hot plates.

  5. Place the wadding (batting) on a flat surface, then the backing fabric right side up, followed by the front panel right side down. Pin around the edges.

  6. Increase your stitch length to 3.5 and stitch through all the layers around your marked circular line, leaving a turning gap of approximately 12cm (4¾in). Trim the seams and snip into the seam allowance at an angle – this will help to produce a smooth curved outline when the mat is turned through. Turn through. Press so that the seam is on the edge, tucking the raw edges of the turning gap inside. Slip stitch the gap closed. Tip Use two layers of insulated wadding (batting), which will help to protect your surfaces from heat.

  7. Fold one of the small strips right sides together, so that it measures 
12 x 3.5cm (4¾ x 13/8in), and stitch along the two short ends, taking a 5mm (¼in) seam allowance. Clip away the excess fabric at the corners and turn the piece through. Press.

  8. Cut a length of bias binding 14cm (5½in) long. Tuck the short ends under and press. Wrap the bias binding around the long raw edge of the strip created in step 7. Pin and stitch the binding in place, close to the edge. Repeat steps 7 and 8 with the other small strip. These strips will hold your cutlery in place.

  9. Small 110425 2f2015 08 14 100601 screen%2bshot%2b2015 08 14%2bat%2b11.06.23

    Lay a knife, fork and spoon to the right-hand side of the mat to determine the position of the strips. Start with the lower strip: place it over the cutlery, about 2.5cm (1in) from the bottom. Pin at the side edges and between each item of cutlery to create three channels. Repeat with the other strip at the top of the cutlery handles. Remove the cutlery and stitch down the pinned lines.

  10. Finish by stitching around the outside edge of the mat, 1cm (½in) from the edge and using a 3.5 stitch length.